3720 Spruce St,

Philadelphia, PA 19104

Mon-Sat 7:00am-7:00pm

Sunday 10:00am-6:00pm

Mon-Sat 7:00am-7:00pm

Sunday 10:00am-6:00pm

3720 Spruce St,

Philadelphia, PA 19104

Increase Water Pressure: 5 Good Techniques

Low Water Pressure In Your Home? Quick Fixes…

A bad shower to begin and end a long day is very uncomfortable. Still, when other household repair work take main concern, you every once in awhile need to learn to cope with low water pressure.

 

Deal with to totally get an excellent stream of water by trying any of the methods listed below, which vary from little modifications to massive jobs.

Talk To Your Next-door neighbors

: Check over with your next-door neighbors to see if they are having a the same concern. The issue might be with the city’s public water supply if this is the case.

 

These systems, like your home’s piping, are prone to leakages, blockages, buildup, and deterioration.

Rusted Damaged Shut-off Water Valve

Q: What is the cause of low water pressure? Can I fix it myself?

A: The average water pressure at a residential property’s inlet valve should be around 40 to 50 psi. Your house might still have lower water pressure than preferred for a range of reasons.

 

  • Where you spot it can help you figure out what’s triggering the issue and whether you can fix it yourself.

 

  • Low water pressure in your region, for example, is most likely an issue that needs to be dealt with by the local area utility.

 

  • Whereas, low water pressure at a specific appliance can usually be traced down to a clogged aerator or a leakage in the water line going to the appliance.

Some jobs are better left to the pros

Consult a Pro. Get No-Commitment Estimates For Your Project.

Check the Water Pressure Yourself

You can check the city water pressure yourself before calling your local company by utilizing a test gauge with a hose connector.

 

Simply screw the gadget onto a hose faucet and turn on the water, after switching off the rest of your property’s faucets and any water-using home appliances (such as the dishwasher and washing machine).

Expert local plumbers admit that readings of 45 or 50 psi are on the low side, 60 is an excellent reading, and 80 or greater is extreme.

 

You can choose what actions to take next after you have either eliminated or validated a pressure issue.

Clear the Obstructions

Mineral deposits can integrate in your pipes with time. In extreme cases, the diameter of the pipes shrinks to the point that they get obstructed, preventing water from easily streaming.

 

Leaving you with a pitiful drip in the shower or a small drip from the faucet.

 

While extreme cases might need the replacement of areas of pipeline, you might at least avoid blockages at your system’s exit points. Cleaning and liquifying any minerals that are obstructing the inner faucet fittings and shower heads will undoubtedly help.

 

Here is how: Simply lay an open zip-lock bag filled with vinegar over your shower head or faucet, secure it with string, and leave it to soak overnight. The next morning all that needs to be done is rinse your cleaned up fittings.

If this approach does not work and you suspect a more serious mineral clog inside the pipes, call a plumbing contractor to examine and fix the issue.

Completely Opened

The following technique takes just a couple of minutes of search. The stream of water into your property’s pipes is controlled by the main water valve, which is normally located near the meter.

 

Find the valve and ensure that it is totally open.

 

If, for example, your pressure drop might be because of a recent property enhancement work. Your service provider might have cut off the main supply of water and simply partially reopened the valve at the end of the task.

 

As a result, stream is limited and pressure is reduced. Luckily, you can change the valve yourself, avoiding the requirement for a plumbing company.

Water Intake Valve Regulator

Change the Regulator

Quite a few homes that use public water have a regulator, which is either set up at the meter or where the service line gets in the residential property and ensures that water does not rush through the pipes.

 

When the regulator fails, the pressure goes down, resulting in a loss of speed that impacts some or all of your home’s components.

 

To deal with the issue, either change this part or reset or better yet, work with a plumbing company to handle the task for you.

Look for Leakages

Water leakages triggered by cracked or damaged pipes can draw out water as it flows through your pipes. Leaving you with at most a trickle at the faucet.

 

To examine if your primary pipeline is damaged, turn off all faucets inside and out, then turn off the water valve in your house and make a note of the number that displays on your water meter.

Return in two hours and take another reading from the meter. Increasing reading suggests a leakage and might indicate that it is time to employ a pro.

Galvanized steel pipes are more susceptible to deterioration with time, so if you choose to change them, opt for first-rate plastic or copper pipes. You should not feel obligated to do this specific repair work yourself:

 

Pipeline replacement requires the services of an experienced plumbing company. While it is a costly job, changing your pipes will do more than at most enhance your showering experience.

 

In addition to increasing pressure and decreasing the possibility of future leakages, changing old plumbing with new can decrease the possibility of corrosives infecting your drinking water, resulting in better quality water.

Put In a Booster Pump for Water Pressure

It’s possible that the issue isn’t with your plumbing system, however with in the area. Gravity and distance are two significant issues that minimize water pressure.

 

If your residence water is forced to travel uphill or a prolonged distance from the local water source, the pressure might be lowered.

Low Pressure Water Booster

When it reaches your home, think about adding a water pressure booster pump to boost the stream rate of the water.

 

The pump costs around $200 or $300, not including the charge of setup which is (better left to a certified plumber).

Some jobs are better left to the pros...

Get No-Commitment Estimates For Your Project

Proud to Install, Repair, and Service the Following Brands: